Hostname: page-component-8448b6f56d-wq2xx Total loading time: 0 Render date: 2024-04-24T00:55:27.571Z Has data issue: false hasContentIssue false
  • English
  • Français

Electron Microscopic Observation on the Structure of Ni(Cu)AI Martensite

Published online by Cambridge University Press:  26 February 2011

Seung-Hyuk Kang ,
Seung-Jun Jeon  and
Hu-Chul Lee
Seung-Hyuk Kang
Affiliation:
Seoul National University, Seoul151–742Korea
Seung-Jun Jeon
Affiliation:
Seoul National University, Seoul151–742Korea
Hu-Chul Lee
Affiliation:
Seoul National University, Seoul151–742Korea
Get access

Abstract

In an effort to seek a way to toughen NiAL intermetallic compounds, deformation characteristics of copper containing NiAL martensite were studied by electron microscopy. Martensite plates with fine {111} <112> internal twins were well developed across the grains in as extruded alloys. Initial linear work hardening up to 7 % strain was observed and the migration of twin interface and martensite plate interfaces were suggested as major deformation modes at this stage. Increase in strain hardening rate after 7 % strain was associated with the development of dislocation structure and growth of new strain induced twins within the internal twin free martensite plates.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 213: Symposium Q – High-Temperature Ordered Intermetallic Alloys IV , 1990 , 385
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Ball, A. and Smallnan, R. E., Acta Metall., 14, 1517 (1966).Google Scholar
2. Inoue, A., Masumoto, T. and Tomioka, H., J. Mater. Sci., 19, 3097 (1984).Google Scholar
3. Field, R. D., Krueger, D. D. and Huang, S. C., High Temperature Ordered Intermetallic Alloys III, ed. by Liu, C. T. et al. , Boston, MA, Materials Reserach Society, 1988, p567.Google Scholar
4. Pank, D. R., Nathal, M. V. and Koss, D. A., High Temperature Ordered Intermetallic Alloys ,III ed. by Liu, C. T. et al. , Boston, MA, Materials Reserach Society, 1988, p561.Google Scholar
5. Guha, S., Munroe, P. R. and Baker, I., High Temperature Ordered Intermetallic Alloys III, ed. by Liu, C. T. et al. , Boston, MA, Materials Research Society, 1988, P633.Google Scholar
6. Enami, K., Martynov, V. V., Tormie, T., Khandros, L. G. and Nenno, S., Trans. Japan Inst. Metals, 22, 357 (1981).Google Scholar
7. Russel, S. M., Law, C. C. and Blackburn., M. J. High Temperature Ordered Intermetallic Alloys III, ed. by Liu, C. T. et al. , Boston, MA, Materials Reserach Society, 1988, p627.Google Scholar
8. Lee, M. H. and Lee, H. C., J. of the Korea Inst. of Metals, Vol.26, No.6, 543 (1988).Google Scholar
9. Chakravorty, S. and Wayman, C. M., Metall. Trans., 7A, 569 (1976)Google Scholar
10. Saburi, T. and Nenno, S. ; Proc. Inter. Conf. Solid Solid Phase Transfortnations, ed. by Aaronson, H. I., Laughlin, D. E., Sekerka, R. F. and Wayman, C. M., AIME, Pittsburgh. PA. USA, 1981, p1455.Google Scholar