Hostname: page-component-7c8c6479df-24hb2 Total loading time: 0 Render date: 2024-03-29T05:25:35.179Z Has data issue: false hasContentIssue false

Electron cyclotron resonance etching characteristics of GaN in plasmas with and without hydrogen

Published online by Cambridge University Press:  21 February 2011

L. Zhang
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
J. Ramer
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
J. Brown
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
K. Zheng
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
L.F. Lester
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
S.D. Hersee
Affiliation:
Center for High Technology Materials, University of New Mexico, Albuquerque, NM 87131
Get access

Abstract

Electron cyclotron resonance (ECR) plasma etching characteristics of gallium nitride (GaN) are investigated using low pressure (4-10 mTorr) SiCl4/Ar and Cl2/H2/Ar ECR discharges. The purpose of this effort is to develop a dry etching process for making laser mirrors on GaN and to examine dry etching processes of GaN that do not require hydrogen, which is known to cause carrier compensation in GaN. The etch rate is found to increase near-linearly with increasing DC bias, and a minimum DC bias of 100V is required to initiate etching in SiCl4/Ar. We have also found that the material quality significantly affects the etch rate. The latter decreases with x-ray rocking curve half-width and increases with defect density. A reasonable etch rate of 660Ǻ/min and good surface morphologies obtained in SiCl/Ar ECR etching make this process suitable for gate recess of an FET. An etch rate of 5270Ǻ/min has been achieved in Cl2/H2/Ar plasmas. This is the highest reported etch rate of GaN so far. The smooth and vertical etch sidewalls (etch to mask selectivity of 16 is obtained) make this process promising for dry-etched laser mirrors on GaN.

Type
Research Article
Copyright
Copyright © Materials Research Society 1996

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1 Nakamura, S., Mukai, T., and Senoh, M., Appl. Phys. Lett. 64, 1678 (1994).Google Scholar
2 Asif Khan, M., Kuznia, J. N., Olson, D. T., Van Hove, J. M., Blasingame, M. and Reitz, L. F. Appl. Phys. Lett. 60, 2917 (1992).Google Scholar
3 Nakamura, S., Jpn. J. Appl. Phys. 30, L1620 (1991).Google Scholar
4 Hersee, S. D., Ramer, J., Zheng, K., Kranenberg, C., Malloy, K., Banas, M., and Goorsky, M., to be published in J. of Electronics Materials, November 1995.Google Scholar
5 McLane, G. F., Casas, L., Pearton, S. J., and Abernathy, C. R., Appl. Phys. Lett. 66, 3328 (1995).Google Scholar
6 Shul, R. J., Kilcoyne, S. P., Hagerott Crawford, M., Parmeter, J. E., Vartuli, C. B., Abernathy, C. R., and Pearton, S. J., Appl. Phys. Lett. 66, 1761 (1995).Google Scholar
7 Adesida, I., Ping, A. T., Youtsey, C., Dow, T., Asif Khan, M., Olson, D. T., and Kuznia, J. N., Appl. Phys. Lett. 65, 889 (1994).Google Scholar
8 Ping, A. T., Adesida, I., Khan, M. A., Appl. Phys. Lett. 67, 1250 (1995).Google Scholar
9 Pearton, S. J., Abernathy, C. R., Vartuli, C. B., Mackenzie, J. D., Shul, R. J., Wilson, R. G., and Zavada, J. M., Electron. Lett. 31, 836 (1995).Google Scholar
10 Van Vechten, J. A., Zook, J. D., Horning, R. D. and Goldenberg, B., Jpn. J. Appl. Phys. 31, 3662 (1992).Google Scholar
11 Nakamura, S., Iwasa, N., Senoh, M., and Mukai, T., Jpn. J. Appl. Phys. 31, L1258 (1992).Google Scholar
12 Lester, L. F., Schaff, W. J., Offsey, S. D., and Eastman, L. F., IEEE Photon. Technol. Lett., 3, 403 (1991).Google Scholar
13 Adesida, I., Mahajan, A., Andideh, E., Asif Khan, M., Olson, D. T., and Kuznia, J. N., Appl. Phys. Lett. 63, 2777 (1993).Google Scholar