Hostname: page-component-7479d7b7d-767nl Total loading time: 0 Render date: 2024-07-10T22:15:03.347Z Has data issue: false hasContentIssue false

Design and Process Issues for Silicon Carbide Power DiMOSFETS

Published online by Cambridge University Press:  21 March 2011

Sei-Hyung Ryu
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
Anant K. Agarwal
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
Nelson S. Saks
Affiliation:
Navel Research Laboratory, 4555 Overlook Avenue Washington, D.C. 20375
Mrinal K. Das
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
Lori A. Lipkin
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
Ranbir Singh
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
John W. Palmour
Affiliation:
Cree, Inc., 4600 Silicon Drive Durham, NC 27703
Get access

Abstract

This paper discusses the design and process issues of high voltage power DiMOSFETs (Double implanted MOSFETs) in 4H-silicon carbide (SiC). Since Critical Field (EC) in 4H-SiC is very high (10X higher than that of a Si), special care is needed to protect the gate oxide. 2D device simulation tool was used to determine the optimal JFET gap, which provides adequate gate oxide protection as well as a reasonable JFET resistance. The other issue in 4H-SiC DiMOSFETs is extremely low effective channel mobility (μeff) in the implanted p-well regions. NO anneal of the gate oxide and buried channel structure are used for increasing μeff. NO anneal, which was reported to be very effective in increasing the μeff of SiC MOSFETS in p-type epilayers, did not produce reasonable μeff of SiC MOSFETs in the implanted p-well. Buried channel (BC) structure with 2.7×1012 cm−2 charge in the channel showed high μeff utilizing bulk buried channel, but resulted in a normally-on device. However, it was shown that by controlling the charge in the BC layer, a normally off device with high μeff can be produced. A 3.3 mm × 3.3 mm DiMOSFET with BC structure showed a drain current of 10 A, which is the highest current reported in SiC power MOSFETs to date, at a forward drop of 4.4 V with a gate bias of only 2.5 V.

Type
Research Article
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Shenoy, J. N., Cooper, J. A. Jr, and Melloch, M. R., “High-Voltage Double-Implanted Power MOSFETs in 6H-SiC,” IEEE Electron Device Letters, Vol.18, pp. 9395, March 1997.Google Scholar
[2] Ueno, K. and Oikawa, T., “Counter-Doped MOSFET's of 4H-SiC,” IEEE Electron Device Letters, Vol.20, No. 12, pp. 624626, December 1999.Google Scholar
[3] Dimitrijev, S., Li, H.-F., Harrison, H. B., and Sweatman, D., “Nitridation of Silicon dioxide Films Grown on 6H Silicon Carbide,” IEEE Electron Device Letters, vol.18, pp. 175177, May 1997.Google Scholar
[4] Chung, G. Y., Tin, C. C., Williams, J. R., McDonald, J. K., Ventra, M. Di, Pantelides, S. T., Feldman, L. C., Weller, R. A., “Effect of nitric oxide annealing on the interface trap densities near the band edges in the 4H polytype of silicon carbide,” Applied Physics Letters, 76(13) pp. 17131715, March 2000.Google Scholar
[5] Das, M. K., Lipkin, L. A., Palmour, J. W., Chung, G. Y., Williams, J. R., McDonald, K., and Feldman, L.C., “High Mobility 4H-SiC Inversion Mode MOSFETs Using Thermally Grown, NO Annealed SiO2,” presented at 58th IEEE Device Research Conference, Denver, CO. June 1921, 2000.Google Scholar
[6] Lipkin, L. A., Slater, D. B. Jr, Palmour, J. W., “Low interface state density oxides on p-type SiC,” Trans Tech Publications. Materials Science Forum, vol.264–268, pt.2, 1998, pp.853–6. Switzerland.Google Scholar