Hostname: page-component-68945f75b7-72kh6 Total loading time: 0 Render date: 2024-08-06T00:54:38.820Z Has data issue: false hasContentIssue false
  • English
  • Français

Deformation of a NI-AL-FE Gamma/Beta Alloy

Published online by Cambridge University Press:  26 February 2011

R. D. Field ,
D. D. Krueger  and
S. C. Huang
R. D. Field
Affiliation:
GE Aircraft Engines, 1 Neumann Way, Cincinnati, OH, 45215
D. D. Krueger
Affiliation:
GE Aircraft Engines, 1 Neumann Way, Cincinnati, OH, 45215
S. C. Huang
Affiliation:
GE Corporate Research and Development Laboratories, PO Box 8, Schenectady, NY, 12301
Get access

Abstract

Room temperature tensile tests were performed on annealed melt-spun ribbons of a 50Ni-20Al-30Fe alloy. The ribbons were found to possess a duplex structure consisting of fcc γ and B2 β grains and exhibited tensile elongations in excess of 10% while still maintaining good strength. The tested specimens were found to contain high dislocation densities in both the γ and β grains, with no indications of stress-induced martensite formation. Dislocation analysis revealed that the vast majority of dislocations in the β have <100> Burgers vectors; however, <111> dislocations were also observed. Slip transfer was often facilitated by specific orientation relationships between the γ and β grains.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 133: Symposium H – High-Temperature Ordered Intermetallic Alloys III , 1988 , 567
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1) Aoki, K and Izumi, O, Nippon Kinzaku Gakkaishi 43, 1190 (1979).Google Scholar
2) Liu, C T, White, C L, and Horton, J A, Acta Met. 33, 213 (1985).Google Scholar
3) Huang, S C, Taub, A I, and Chang, K M, Acta Met. 32, 1703 (1984).Google Scholar
4) Mises, R von, angew, Z.. Math. Mech. 8, 161 (1928).Google Scholar
5) Ball, A and Smallman, R E, Acta Met. 14, 1349 (1966).CrossRefGoogle Scholar
6) Pascoe, R T and Newey, C W A, Met. Sci. J. 2, 138 (1968).Google Scholar
7) Wasilewski, R J, Butler, S R, and Hanlon, J E, Trans. AIME 239, 1357 (1967).Google Scholar
8) Gaydosh, D J, Jech, R W, and Titran, R H, J. Mat. Sci. Letters 4, 138 (1985).CrossRefGoogle Scholar
9) Inoue, A, Masumoto, T, and Tomioka, H, J. Mat. Sci. 19, 3097 (1984).Google Scholar
10) Taub, A, Palmer, C P, Chang, K M, and Huang, S C, in Mechanical Behavior of Rapidly Solidified Materials, Proceedings: AIME Annual Meeting, Feb. 1985.Google Scholar
11) Enami, K, Hasunuma, J, Nagasawa, A, and Nenno, S, Scripta Met. 10, 879 (1976).CrossRefGoogle Scholar
12) Reynaud, F., Scripta Met. 11, 765 (1977).Google Scholar
13) Lasalmonie, A, Proceedings of the 6th European Congress of Electron Microscopy, Jerusalem, Sept. 14–20, 1976.Google Scholar
14) Loretto, M H and Wasilewski, R J, Phil. Mag. 23, 1311 (1971).Google Scholar
15) Schulson, E M and Baker, D R, Scripta Met. 17, 519 (1983).CrossRefGoogle Scholar
16) Pops, H, Met. Trans. 1, 251 (1970).Google Scholar
17) Mohamed, H A and Washburn, J, Met. Trans. 7A, 1041 (1976).CrossRefGoogle Scholar
18) Enami, K and Nenno, S, Met. Trans. 2, 1487 (1971).Google Scholar
19) Nagasawa, A, Enami, K, Ishino, Y, Abe, Y, and Nenno, S, Scripta Met. 8, 1055 (1974).Google Scholar
20) Guha, S, Monroe, P R, and Baker, I, in Symposium H: High Temperature Ordered Intermetallic Alloys (Mater. Res. Soc. Proc., Boston, Ma, 1988).Google Scholar
21) Rivlin, V G and Raynor, G V (review #251), Int. Met. Rev. 1980, #3, 79.Google Scholar