Hostname: page-component-77c89778f8-rkxrd Total loading time: 0 Render date: 2024-07-21T23:50:45.215Z Has data issue: false hasContentIssue false

Cold-Deformation and Annealing of equiaxed L1o-ordered FePd Intermetallics

Published online by Cambridge University Press:  26 February 2011

Anirudha Desphande
Affiliation:
anirudha.desphande@ge.comUniversity of PittsburghDept. of Materials Science and EngineeringGE-lighting technologyWilloughby OH 44094United States
Jorg Wiezorek
Affiliation:
wiezorek@pitt.edu, University of Pittsburgh, Dept. of Materials Science and Engineering, 848 Benedum Hall, Pittsburgh, PA, 15261, United States
Get access

Abstract

The L10 ordering equiatomic intermetallic FePd has been used as a model system for the investigation of the evolution of microstructure and properties during annealing at temperatures below the ordering temperature after deformation in the L10 state. The two different routes for the preparation of equiaxed L10 FePd polycrystals, annealing after cold deformation in the disordered FCC state or after cold deformation in the ordered state, produce similar grain size distributions, differ in the transformation kinetics and importantly in the sequence of texture evolution during the post-cold-deformation annealing. Cold deformed L10 FePd progresses through the classic stages of annealing known from studies of disordered elemental metals and alloys based on them. The reduced L10 SLRO of the ‘mechanically disordered’ FePd is recovered in the early stages of annealing and both the recrystallization and the grain growth stages are quite sluggish, presumably because of the slow diffusion processes in the L10 lattice.

Type
Research Article
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Cahn, R.W. (1990) in : Recovery, Strain-Age-Hardening and Recrystallization in Deformed Intermetallics, High Temperature Aluminides and Intermetallics, ed. Whang, S.H. et al. (TMS: Warrendale, PA), p245 Google Scholar
2. Cahn, R.W. (1996) in: Physical metallurgy vol-3, pp 2427, eds. Cahn, R.W. and Haasen, P., North Holland Publishing Co.: New York, NY;Google Scholar
3. Greenberg, B. A., Hug, G., Antonova, O.V., Boyarshinova, T.S., Pesina, Z.M., Sachanskaya, I.N., Yu., A., Volkov (1997) Intermetallics vol 5, p297;Google Scholar
4. Arunachalam, V.S., Cahn, R.W., (1967) J Mater. Sci. vol 2, p160;10.1007/BF00549575Google Scholar
5. Gottstein, G., Nagpal, P., Kim, W. (1989) Mater. Sci. Eng. vol A108,p165;10.1016/0921-5093(89)90418-8Google Scholar
6. Cahn, R. W., Takeyama, M., Horton, J.A., Liu, C.T. (1991) J. Mater. Res. vol 6, p57;10.1557/JMR.1991.0057Google Scholar
7. Deshpande, A.R., Ph.D. thesis, University of Pittsburgh 2005, ‘ANNEALING BEHAVIOR OF HEAVILY COLD DEFORMED, EQUIATOMIC, FERROMAGNETIC Fe-Pd INTERMETALLICS’Google Scholar
8. Deshpande, A. R., Al-Ghaferi, A., Xu, H., Heinrich, H., Wiezorek, J.M.K (2003) in : Nanostructural design of advanced materials: A commemorative volume on Prof. G. Thomas' seventieth birthday. London Elsevier, p129;10.1016/B978-008044373-7/50040-1Google Scholar
9. Deshpande, A.R., Wiezorek, J.M.K., (2004), Magnetism, J. and Magnetic Mater. vol 270, p157;10.1016/j.jmmm.2003.08.013Google Scholar
10. Deshpande, A.R., Wiezorek, J.M.K., (2006), Z. F. Metallkunde vol. 97, p304.10.3139/146.101255Google Scholar