Hostname: page-component-848d4c4894-mwx4w Total loading time: 0 Render date: 2024-07-01T01:20:43.032Z Has data issue: false hasContentIssue false
  • English
  • Français

Analysis of the Mechanical Failure in a Multilayered Thin Film System Tested by Microtensile Loading

Published online by Cambridge University Press:  15 February 2011

T. Marieb ,
M. Ignat ,
H. Fujimoto  and
P. Flinn
T. Marieb
Affiliation:
Intel Corporation, 3065 Bowers Ave., Santa Clara, CA 95052
M. Ignat
Affiliation:
INP Grenoble, LTPCM ENSEEG, St. Martin D'Heres, France
H. Fujimoto
Affiliation:
Intel Corporation, 3065 Bowers Ave., Santa Clara, CA 95052
P. Flinn
Affiliation:
Intel Corporation, 3065 Bowers Ave., Santa Clara, CA 95052
Get access

Abstract

Multilayered thin films were deposited on pure Al substrate test bars for in situ scanning electron microscope (SEM) microtensile deformation. The films consisted of a TiN layer covered by either SiO2 or W. Deformation of the samples showed that the TiN film dominated cracking events and caused cracking in the W to occur at lower critical stress values than previously reported. Crack deflections along the TiN-W interface were also seen. W film strain was measured by X-ray diffraction before and after testing to look at the effect of cracking and deformation on stress in this film.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 391: Symposium T – Materials Reliability in Microelectronics V , 1995 , 85
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1 Scafidi, P., Ignat, M., Dupeux, M., in Materials Reliability in Microelectronics III, edited by Rodbell, K.P., Filter, W.F., Frost, H.J., Ho, P.S. (Mater. Res. Soc. Symp. Proc.,. 309, Pittsburgh, PA, 1993) pp. 55–60.Google Scholar
2 Ignat, M., Scafidi, P., Duloisy, E., Dijon, J., in Materials Reliability in Microelectronics IV, edited by Borgesen, P., Coburn, J.C., Sanchez, J.E. Jr., Rodbell, K.P., Filter, W.F. (Mater. Res. Soc. Symp. Proc.,. 338, Pittsburgh, PA, 1994) pp. 135–146.Google Scholar
3 Maniguet, L., Ignat, M., Dupeux, M., Flinn, P.A.,Normandon, Ph., Gergaud, P., Bacmann, J.J., in Advanced Metallization for ULSI Applications, edited by Cale, T.S. and Pintchovski, F.S. (Mater. Res. Soc. Proc., Pittsburgh, PA, 1993) pp. 67–72.Google Scholar
4 Hu, M.S. and Evans, A.G., Acta Metall. 37, 917 (1989).Google Scholar
5 Kelly, A., Strong Solids, 2nd ed. (Oxford University Press, 1973), Chapter 5.Google Scholar
6 Laugier, M.T., J. Mat. Sci. 21, 2269 (1986).Google Scholar
7 Ashby, M.F., Gandhi, C., Taplin, D.M., Acta Metall. 27, 699 (1979).Google Scholar
8 Frost, H.J., Ashby, M.F., Deformation-Mechanism Maps, (Pergamon Press, 1982).Google Scholar
9 Tassot, P., Rev. de Metall. CIT Feb. 1988, 165.Google Scholar