Hostname: page-component-cc8bf7c57-77pjf Total loading time: 0 Render date: 2024-12-11T04:56:05.176Z Has data issue: false hasContentIssue false

Transformation Behavior of TiNiPt Thin Films Fabricated Using Melt Spinning Technique

Published online by Cambridge University Press:  26 February 2011

Tomonari Inamura
Affiliation:
Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama, Kanagawa 226–8503, Japan.
Yohei Takahashi
Affiliation:
Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama, Kanagawa 226–8503, Japan.
Hideki Hosoda
Affiliation:
Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama, Kanagawa 226–8503, Japan.
Kenji Wakashima
Affiliation:
Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama, Kanagawa 226–8503, Japan.
Takeshi Nagase
Affiliation:
Department of Materials Science & Engineering, Graduate School of Engineering, Osaka University, Suita, Osaka 565–0871, Japan.
Takayoshi Nakano
Affiliation:
Department of Materials Science & Engineering, Graduate School of Engineering, Osaka University, Suita, Osaka 565–0871, Japan.
Yukichi Umakoshi
Affiliation:
Department of Materials Science & Engineering, Graduate School of Engineering, Osaka University, Suita, Osaka 565–0871, Japan.
Shuichi Miyazaki
Affiliation:
Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305–8573, Japan.
Get access

Abstract

Martensitic transformation behavior of Ti50Ni40Pt10 (TiNiPt) melt-spun ribbons were investigated where the heat treatment temperature was systematically changed from 473K to 773K. A hot-forged bulk TiNiPt material with the similar chemical composition was also tested as a comparison. θ-2θ X-ray diffraction analysis and transmission electron microscopy observation revealed that the as-spun ribbons were fully crystallized. The apparent phases of as-spun ribbons at room temperature are both B19 martensite and B2 parent phase instead of B2 single phase for the hot-forged bulk material. No precipitates were found in as-spun and heat-treated ribbons. It was revealed by differential scanning calorimetry that all the specimens exhibit one-step transformation. The martensitic transformation temperatures of the TiNiPt as-spun ribbons are 100K higher than those of the hot-forged bulk material, and the martensitic transformation temperature decreases with increasing heat treatment temperature.

Type
Research Article
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Saburi, T., “Ti-Ni Shape Memory Alloys”, Shape Memory Materials, ed. Otsuka, K. and Wayman, C. M. (Cambridge University Press, 1998) pp. 4996.Google Scholar
2. Van Humbeeck, J. and Firstov, G. in Proc. of The Forth Pacific Rim Int. Conf., edited by. S. Hanada et al. (The Japan Ints. Metals, 2001) pp.18711874.Google Scholar
3. Khachin, V. N., Pushin, V. G., Sivokha, V. P., Kondrat'yev, V.V., Muslov, S. A., Voronin, V. P., Zolotukhin, Yu. S. and Yurchenko, L. I., Phys. Met. Metall. 67, 125 (1989)Google Scholar
4. Hosoda, H., Tsuji, M., Mimura, M., Takahashi, Y., Wakashima, K. and Yamabe-Mitarai, Y., Mat. Res. Soc. Symp. Proc., 753, BB5.51.4 (2003)Google Scholar
5. Hosoda, H., Tsuji, M., Takahashi, Y., Inamura, T., Wakashima, K., Yamabe-Mitarai, Y., Miyazaki, S. and Inoue, K., Mater. Sci. Forum, 426–432, 2333 (2003)Google Scholar
6. Tsuji, M., Hosoda, H., Wakashima, K. and Yamabe-Mitarai, Y., Mat. Res. Soc. Symp. Proc., 753, BB5.52.1 (2003)Google Scholar
7. Takahashi, Y., Tsuji, M., Sakurai, J., Hosoda, H., Wakashima, K. and Miyazaki, S., Trans. MRS-J., 28, 627 (2003)Google Scholar
8. Cesari, E., Ochin, P., Portier, R., Kolomytsev, V., Koval, Yu., Pasko, A., Soolshenko, V., Mater. Sci. Eng., A273–275, 733 (1999)Google Scholar
9. Chang, L. C. and Read, T. A., Trans. AIME, 189, 47 (1951)Google Scholar
10. Otsuka, K., Sawamura, T. and Shimizu, K., Phys. Stat. Sol., 5, 457 (1971)Google Scholar
11. Lieberman, D. S., Wechsler, M. S. and Read, T. A., J. Appl. Phys., 26, 473 (1955)Google Scholar