Hostname: page-component-7bb8b95d7b-qxsvm Total loading time: 0 Render date: 2024-09-20T04:09:14.444Z Has data issue: false hasContentIssue false
  • English
  • Français

Theoretical analysis of the relationships between hardness, elastic modulus, and the work of indentation for work-hardening materials

Published online by Cambridge University Press:  31 January 2011

Rong Yang ,
Taihua Zhang  and
Yihui Feng
Rong Yang
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China; and Graduate University of Chinese Academy of Sciences, Beijing 100049, China
Taihua Zhang*
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
Yihui Feng
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China; and Graduate University of Chinese Academy of Sciences, Beijing 100049, China
*
a)Address all correspondence to this author. e-mail: zhangth@lnm.imech.ac.cn.
Get access

Abstract

In our previous paper, the expanding cavity model (ECM) and Lamé solution were used to obtain an analytical expression for the scale ratio between hardness (H) to reduced modulus (Er) and unloading work (Wu) to total work (Wt) of indentation for elastic-perfectly plastic materials. In this paper, the more general work-hardening (linear and power-law) materials are studied. Our previous conclusions that this ratio depends mainly on the conical angle of indenter, holds not only for elastic perfectly-plastic materials, but also for work-hardening materials. These results were also verified by numerical simulations.

Keywords

NanoindentationHardnessStress/Strain Relationship
Type
Materials Communications
Information
Journal of Materials Research , Volume 25 , Issue 11 , November 2010 , pp. 2072 - 2077
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Pharr, G.M., Cheng, Y.T., Hutchings, I.M., Sakai, M., Moody, N.R., Sundararajan, G., Swain, M.V.: Indentation methods in advanced materials research introduction. J. Mater. Res. 24, 579 (2009)CrossRefGoogle Scholar
2.Oliver, W.C., Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992)CrossRefGoogle Scholar
3.Cheng, Y.T., Cheng, C.M.: Relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 73, 614 (1998)CrossRefGoogle Scholar
4.Alkorta, J., Martinez-Esnaola, J.M., Sevillano, J.G.: Comments on “Comment on the determination of mechanical properties from the energy dissipated during indentation” by J. Malzbender [J. Mater. Res. 20, 1090 (2005)]. J. Mater. Res. 21, 302 (2006)CrossRefGoogle Scholar
5.Malzbender, J.: Reply to the comments on “Comment on the determination of mechanical properties from the energy dissipated during indentation” by J. Malzbender [J. Mater. Res. 20, 1090 (2005)]. J. Mater. Res. 21, 306 (2006)CrossRefGoogle Scholar
6.Chen, J., Bull, S.J.: Relation between the ratio of elastic work to the total work of indentation and the ratio of hardness to Young's modulus for a perfect conical tip. J. Mater. Res. 24, 590 (2009)CrossRefGoogle Scholar
7.Yang, R., Zhang, T.H., Jiang, P., Bai, Y.L.: Experimental verification and theoretical analysis of the relationships between hardness, elastic modulus, and the work of indentation. Appl. Phys. Lett. 92, 231906 (2008)CrossRefGoogle Scholar
8.Johnson, K.L.: Contact Mechanics (Cambridge University Press, Cambridge 1985)CrossRefGoogle Scholar
9.Gao, X.L., Jing, X.N., Subhash, G.: Two new expanding cavity models for indentation deformations of elastic strain-hardening materials. Int. J. Solids Struct. 43, 2193 (2006)CrossRefGoogle Scholar
10.Gao, X.L.: Elasto-plastic analysis of an internally pressurized thick-walled cylinder using a strain gradient plasticity theory. Int. J. Solids Struct. 40, 6445 (2003)CrossRefGoogle Scholar
11.Hill, R.: The Mathematical Theory of Plasticity (Oxford University Press, New York 1998)CrossRefGoogle Scholar
12.ABAQUS HKS Inc, Pawtucket, RIGoogle Scholar
13.Ma, D.J., Ong, C.W.: Further analysis of energy-based indentation relationship among Young's modulus, nominal hardness, and indentation work. J. Mater. Res. 25, 1131 (2010)CrossRefGoogle Scholar