Hostname: page-component-76fb5796d-r6qrq Total loading time: 0 Render date: 2024-04-26T22:01:43.767Z Has data issue: false hasContentIssue false
  • English
  • Français

Nanoindentation and nanoscratch of a thermal oxide layer on a FeAl alloy

Published online by Cambridge University Press:  03 March 2011

J. Xia ,
C.X. Li ,
H. Dong  and
T. Bell
J. Xia*
Affiliation:
Department of Metallurgy and Materials, School of Engineering, The University of Birmingham, Birmingham B15 2TT, United Kingdom
C.X. Li
Affiliation:
Department of Metallurgy and Materials, School of Engineering, The University of Birmingham, Birmingham B15 2TT, United Kingdom
H. Dong
Affiliation:
Department of Metallurgy and Materials, School of Engineering, The University of Birmingham, Birmingham B15 2TT, United Kingdom
T. Bell
Affiliation:
Department of Metallurgy and Materials, School of Engineering, The University of Birmingham, Birmingham B15 2TT, United Kingdom
*
a)Address all correspondence to this author. e-mail: jxx096@bham.ac.uk
Get access

Abstract

An iron aluminide (Fe–40 at.% Al) was thermal oxidation (TO)-treated at 1000 °C for 30 to 150 h. The mechanical properties (e.g., hardness and elastic modulus), the scratch resistance, the deformation and damage behaviors of the TO-treated surface layers were evaluated using nanoindentation and nanoscratch techniques. It has been found that the TO treatment produced an oxide layer containing α–Al2O3 on the iron aluminide surface, which increased the surface hardness (H) and elastic modulus (Er) but reduced the ratio of Er/H. This has significantly improved the scratch resistance of the iron aluminide. Longer treatment resulted in a thicker oxide layer and led to further reduced scratch rate and an increased critical load to failure. The scratch resistance has been correlated with the scratch load, the hardness, and the Er/H ratio of the surface oxide layer.

Keywords

NanoindentationTribologyMechanical properties
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 1 , January 2004 , pp. 291 - 300
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Stoloff, N.S. in High Temperature Ordered Intermetallic Alloys, edited by Koch, C.C., Liu, C.T., and Stoloff, N.S. (Mater. Res. Soc. Symp. Proc. 39, Pittsburgh, PA, 1985), p. 3.Google Scholar
2.Stephens, J.R. in High Temperature Ordered Intermetallic Alloys, edited by Koch, C.C., Liu, C.T., and Stoloff, N.S. (Mater. Res. Soc. Symp. Proc. 39, Pittsburgh, PA, 1985), p. 395.Google Scholar
3.Liu, C.T., George, E.P., Maziasz, P.J. and Schneibel, J.H., Mater. Sci. Eng. A 258 84 (1998).CrossRefGoogle Scholar
4.Kim, Y.S. and Kim, Y.HMater. Sci. Eng. A 258, 319 (1998).CrossRefGoogle Scholar
5.Hawk, J.A. and Alman, D.E., Mater. Sci. Eng. A 239–240 899 (1997).CrossRefGoogle Scholar
6.Maupin, H.E., Wilson, R.D. and Hawl, J.A., Wear 162–164 432 (1993).CrossRefGoogle Scholar
7.Guan, X.S., Zhu, S.M., Shibata, K. and Iwasaki, K., Mater. Trans. 43 1325 (2002).CrossRefGoogle Scholar
8.Alman, D.E., Hawk, J.A., Tylczak, J.H., Doğan, C.P. and Wilson, R.D., Wear 251 875 (2001).CrossRefGoogle Scholar
9.Dong, H. and Bell, T., Wear 238 131 (2000).CrossRefGoogle Scholar
10.McColm, I.J.Ceramic Hardness (Plenum Press, New York, 1990), p. 259.CrossRefGoogle Scholar
11.Pint, B.A., Tortorelli, P.F. and Wright, I.G. in Oxidation of Intermetallics, edited by Grabke, H.J. and Schütze, M. (Wiley-VCH, New York, 1997), p. 183.CrossRefGoogle Scholar
12.Montealegre, M.A., González-Carrasco, J.L., Muñoz-Morris, M.A., Chao, J. and Morris, D.G., Intermetallics 8 439 2000.CrossRefGoogle Scholar
13.Xia, J., Li, C.X. and Dong, H., Mater. Sci. Eng. A 354 112 (2003).CrossRefGoogle Scholar
14.Oliver, W.C. and Pharr, G.M., J. Mater. Res. 7 1564 (1992).CrossRefGoogle Scholar
15.Hutchings, I.M.Tribology: Friction and Wear of Engineering Materials (Edward Arnold, London, 1992), p. 150.Google Scholar
16.Hutchings, I.M.Tribology: Friction and Wear of Engineering Materials (Edward Arnold, London, 1992), p. 83.Google Scholar
17.Bhushan, B., Wear 251 1105 (2001).CrossRefGoogle Scholar
18.Greenwood, J.A. and Williamson, J.B.P., Proc. R. Soc. (London) A 295 300 (1966).Google Scholar
19.Hutchings, I.M.Tribology: Friction and Wear of Engineering Materials (Edward Arnold, London, 1992), p. 20.Google Scholar
20.Leyland, A. and Matthews, A., Wear 246 1 (2000).CrossRefGoogle Scholar