Hostname: page-component-77c89778f8-m42fx Total loading time: 0 Render date: 2024-07-17T17:46:26.687Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure evolution and mechanical properties of Zr–45Ti–5Al–3V alloy processed by electric field-assisted extrusion

Published online by Cambridge University Press:  02 November 2016

Chunxiang Zhang ,
Limin Wang ,
Riping Liu ,
Bojun Zhao  and
Junting Luo
Chunxiang Zhang
Affiliation:
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
Limin Wang
Affiliation:
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
Riping Liu
Affiliation:
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
Bojun Zhao
Affiliation:
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China
Junting Luo*
Affiliation:
State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China; and Education Ministry Key Laboratory of Advanced Forging & Stamping Technology and Science, Yanshan University, Qinhuangdao 066004, China
*
a)Address all correspondence to this author. e-mail: luojunting@ysu.edu.cn
Get access

Abstract

The electric field-assisted extrusion process is applied in Zr–45Ti–5Al–3V alloy. A transition from phase α to phase β is observed at various zones during the extrusion, and a complete transition is achieved by the considerable shear deformation. When subjected to the electric field-assisted extrusion, the continuous dynamic recrystallization is significant at the edges and the major shear deformation zones, and the equiaxed phase β grain structure is refined to a size of 250–300 µm. In addition, the phase β grains contain a minor amount of large residual lath-shaped phase α structures. The edges and the major shear deformation zones form a cubic texture along the {100}〈001〉 direction with a slightly weak polarity, while the polarity of the texture at the center is strong. The extrusion is found to decrease the edge strength from 1580 MPa to 1185 MPa and to increase the elongation up to 7.2%.

Keywords

alloycrystalmicrostructure
Type
Articles
Information
Journal of Materials Research , Volume 31 , Issue 22 , 28 November 2016 , pp. 3580 - 3587
Check for updates
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Griffiths, M.: A review of microstructure evolution in zirconium alloys during irradiation. J. Nucl. Mater. 159(159), 190 (1988).Google Scholar
Kim, H.G., Park, S.Y., Lee, M.H., Yong, H.J., and Sun, D.K.: Corrosion and microstructural characteristics of Zr–Nb alloys with different Nb contents. J. Nucl. Mater. 373(1–3), 429 (2008).Google Scholar
Zander, D. and Köster, U.: Corrosion of amorphous and nanocrystalline Zr-based alloys. Mater. Sci. Eng., A 375–377, 53 (2004).Google Scholar
Sabirov, I., Perez-Prado, M.T., Molina-Aldareguia, J.M., Semenova, I.P., Salimgareeva, G.Kh., and Valiev, R.Z.: Anisotropy of mechanical properties in high-strength ultra-fine-grained pure Ti processed via a complex severe plastic deformation route. Scr. Mater. 64(1), 69 (2011).CrossRefGoogle Scholar
Ho, W.F., Chen, W.K., Wu, S.C., and Hsu, H.C.: Structure, mechanical properties, and grindability of dental Ti–Zr alloys. J. Mater. Sci.: Mater. Med. 19(10), 3179 (2008).Google Scholar
Shi, Y.D., Li, M., Guo, D.F., Zhang, G.S., Zhang, Q., Li, X.H., and Zhang, X.Y.: A hierarchical and multiphase nanolaminated alloy with an excellent combination of tensile properties. Mater. Sci. Eng., A 615, 464 (2014).Google Scholar
Li, M., Guo, D.F., Zhang, Q., Ma, T.Y., Shi, Y.D., Zhang, G.S., Li, X.H., and Zhang, X.Y.: Simultaneously enhancing fracture toughness and strength in a hierarchical nanolamella-structured alloy. Mater. Sci. Eng., A 612, 1 (2014).Google Scholar
Tan, Y.B., Duan, J.L., Yang, L.H., Liu, W.C., Zhang, J.W., and Liu, R.P.: Hot deformation behavior of Ti–20Zr–6.5Al–4V alloy in the α + β and single β phase field. Mater. Sci. Eng., A 609, 226 (2014).CrossRefGoogle Scholar
Tiwari, D., Basu, B., Biswas, K., and Biswas, K.: Simulation of thermal and electric field evolution during spark plasma sintering. Scr. Mater. 35(2), 699 (2009).Google Scholar
Wang, C., Cheng, L.F., and Zhao, Z.: FEM analysis of the temperature and stress distribution in spark plasma sintering: Modelling and experimental validation. Comput. Mater. Sci. 49(2), 351 (2010).Google Scholar
Pavia, A., Durand, L., Ajustron, F., Bley, V., Chevallier, G., Peigney, A., and Estournès, C.: Electro-thermal measurements and finite element method simulations of a spark plasma sintering device. J. Mater. Process. Technol. 213(8), 1327 (2013).Google Scholar
Liang, S.X., Ma, M.Z., Jing, R., Tan, C.L., and Liu, R.P.: Structural evolution and mechanical properties of Zr–45Ti–5Al–3V alloy by heat treatments. Mater. Sci. Eng., A 541, 67 (2015).Google Scholar
Shen, X., Yu, P.F., Jing, Q., Yao, Y., Gu, L., Wang, Y.G., Duan, X.F., Yu, R.C., and Liu, R.P.: Transmission electron microscopy observations of structural modulation in the phase transition from α-Zr to ω-Zr induced by shear strain. Scr. Mater. 67(s7–8), 653 (2012).CrossRefGoogle Scholar
Humphreys, F.J.: Review grain and subgrain characterisation by electron backscatter diffraction. J. Mater. Sci. 36(16), 3833 (2001).CrossRefGoogle Scholar
Polkowski, W., Jóźwik, P., and Bojar, Z.: EBSD and X-ray diffraction study on the recrystallization of cold rolled Ni3Al based intermetallic alloy. J. Alloys Compd. 614(614), 226 (2014).Google Scholar