Hostname: page-component-8448b6f56d-qsmjn Total loading time: 0 Render date: 2024-04-25T06:09:22.392Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of laser beam irradiation on AISI 1045 steel

Published online by Cambridge University Press:  31 January 2011

M. Riabkina-Fishman ,
J. Zahavi  and
L. S. Zevin
M. Riabkina-Fishman
Affiliation:
Israel Institute of Metals, Technion, Haifa, Israel 32000
J. Zahavi
Affiliation:
Israel Institute of Metals, Technion, Haifa, Israel 32000
L. S. Zevin
Affiliation:
Institute of Applied Research, Ben-Gurion University of the Negev. Beer-Sheva, Israel
Get access

Abstract

The effect of the parameters of laser irradiation (beam power and travel velocity) as well as of various surface coatings and protecting atmospheres on the size, structure, and hardness of the laser-affected region was studied in the case of commercial 1045 steel and a continuous CO2 laser. The action of the laser beam depends more strongly on its traverse velocity than on its power. When the power density exceeds a certain threshold level, a drastic decrease in the size of the laser-affected region takes place. The action can be enhanced by surface treatment in orthophosphoric acid as well as by some painted surface coatings. Unlike the latter, electroplated Cr and Ni layers were found to cause substantial alloying of the laser-treated layer. The laser-affected region formed by a single pass consists of two distinct zones: a melt zone, surrounded by an austenitization zone with a duplex structure representing former pearlite and ferrite regions. The hardness of the melt zone (about HV 750) exceeds that of conventionally hardened 1045 steel; even higher values (up to HV 900) are observed in the former pearlite regions of the austeniti zation zone, that of the former ferrite regions being about HV 250. In the case of an extended surface processed by a series of equidistant passes, a relatively wide region of tempered martensite is formed (with minimum hardness values down to HV 400) due to the heating generated by each pass in the previously hardened layer. As a result, a periodic hardness distribution is observed, whose fcatures depend on the degree of overlapping. High tensile residual stresses were found by x-ray diffraction in surface layers both in the cases of overlapping and separated passes.

Type
Articles
Information
Journal of Materials Research , Volume 3 , Issue 6 , December 1988 , pp. 1108 - 1118
Copyright
Copyright © Materials Research Society 1988

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Molian, P. A., Mater. Sci. Eng. 51, 253 (1981).CrossRefGoogle Scholar
2Benedek, J., Shachrai, A., and Levin, L., Opt. Laser Technol. 1980 247 (October).CrossRefGoogle Scholar
3Banas, M. and Webb, R., Proc. IEEE 70, 556 (1982).CrossRefGoogle Scholar
4Moore, P. G. and McCafferty, E., J. Electrochem. Soc. 128, 1391 (1981).CrossRefGoogle Scholar
5Gnanamuthu, D. S., Opt. Eng. 19, 783 (1980).CrossRefGoogle Scholar
6Moore, P. G. and Weinman, L. S., Proc. Soc. Photo-Opt. Instr. Eng. 198, 120 (1979).Google Scholar
7Duley, W. W., Laser Processing and Analysis of Materials (Plenum, New York, 1981), p. 116.Google Scholar
8Ready, J. F., Proc. IEEE 70, 533 (1982).CrossRefGoogle Scholar
9Mordike, B. L., Bergmann, H. W., and Gross, N., Z. Werkstofftech. 14, 253 (1983).CrossRefGoogle Scholar
10Rykalin, N. N., Uglov, A. A., Grebennikov, V. A., and Ignatiev, M. V., Dokl. Akad. Nauk SSSR 272, 1110 (1983).Google Scholar
11Uglov, A. A.et ah, Fiz. Khim. Obrab. Mater. 18 (2), 3 (1984).Google Scholar
12Uglov, A. A.et ah, Fiz. Khim. Obrab. Mater. 20 (3), 18 (1986).Google Scholar
13Solina, A., Sanctis, M. De, Paganini, L., Blarasin, A., and Quaranta, S., J. Heat Treating 3 (3), 194 (1984).CrossRefGoogle Scholar
14Lamb, M., West, D. R. F., and Stern, W. M., Mater. Sci. Technol. 2, 974 (1986).CrossRefGoogle Scholar
15James, M. R., Gnanamuthu, D. S., and Moores, R. J., Scripta Metal. 18, 357 (1984).CrossRefGoogle Scholar