Hostname: page-component-7c8c6479df-ws8qp Total loading time: 0 Render date: 2024-03-19T03:07:36.364Z Has data issue: false hasContentIssue false

Determination of the individual phase properties from the measured grid indentation data

Published online by Cambridge University Press:  19 October 2016

Petr Haušild*
Affiliation:
Faculty of Nuclear Sciences and Physical Engineering, Department of Materials, Czech Technical University in Prague, 120 00 Praha 2, Czech Republic
Aleš Materna
Affiliation:
Faculty of Nuclear Sciences and Physical Engineering, Department of Materials, Czech Technical University in Prague, 120 00 Praha 2, Czech Republic
Lenka Kocmanová
Affiliation:
Faculty of Nuclear Sciences and Physical Engineering, Department of Materials, Czech Technical University in Prague, 120 00 Praha 2, Czech Republic
Jiří Matějíček
Affiliation:
Institute of Plasma Physics, The Czech Academy of Sciences, 182 00 Praha, Czech Republic
*
a) Address all correspondence to this author. e-mail: petr.hausild@fjfi.cvut.cz
Get access

Abstract

Statistical distribution of grid indentation data measured in multiphase materials can be significantly affected by the presence of an interface between adjacent materials. The influence of an interface on the distribution of measured indentation moduli was therefore characterized in model metal–metal, ceramic–ceramic, and metal-ceramic composites. The change of properties near the interface was simulated by finite element method and experimentally verified by indentation in proximity of the boundary between two phases with distinctly different mechanical properties varying the depth of penetration and the distance from the interface. Subsequently, the conditional probability of measuring near the interface was quantified by beta distribution function with parameters dependent on the size of the volume/area affected by the presence of the interface. Using this approach, the intrinsic properties of the individual materials were successfully extracted from the experimental grid indentation data.

Type
Articles
Copyright
Copyright © Materials Research Society 2016 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Doerner, M.F. and Nix, W.D.: A method for interpreting the data from depth-sensing indentation instruments. J. Mater. Res. 1, 601 (1986).Google Scholar
Menčík, J., Munz, D., Quandt, E., Weppelmann, E.R., and Swain, M.V.: Determination of elastic-modulus of thin-layers using nanoindentation. J. Mater. Res. 12, 2475 (1997).Google Scholar
Oliver, W.C. and Pharr, G.M.: Improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).Google Scholar
Oliver, W.C. and Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).Google Scholar
ISO 14577-1: Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method (ISO 14577-1:2015).Google Scholar
Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
Constantinides, G., Ravi Chandran, K.S., Ulm, F-J., and Van Vliet, K.J.: Grid indentation analysis of composite microstructure and mechanics: Principles and validation. Mater. Sci. Eng., A 430, 189 (2006).Google Scholar
Randall, N.X., Vandamme, M., and Ulm, F-J.: Nanoindentation analysis as a two-dimensional tool for mapping the mechanical properties of complex surfaces. J. Mater. Res. 24, 679 (2009).Google Scholar
Durst, K., Göken, M., and Vehoff, H.: Finite element study for nanoindentation measurements on two-phase materials. J. Mater. Res. 19, 8594 (2004).Google Scholar
Haušild, P., Nohava, J., and Pilvin, P.: Characterisation of strain-induced martensite in a metastable austenitic stainless steel by nanoindentation. Strain 47, 129 (2011).Google Scholar
Nohava, J., Haušild, P., Houdková, Š., and Enžl, R.: Comparison of isolated indentation and grid indentation methods for HVOF sprayed cermets. J. Therm. Spray Technol. 21, 651 (2012).Google Scholar
Vlassak, J.J. and Nix, W.D.: Indentation modulus of elastically anisotropic half spaces. Philos. Mag. A 67, 1045 (1993).Google Scholar
Vlassak, J.J. and Nix, W.D.: Measuring the elastic properties of anisotropic materials by means of indentation experiments. J. Mech. Phys. Solids 42, 1223 (1994).Google Scholar
Haušild, P., Materna, A., and Nohava, J.: Characterization of anisotropy in hardness and indentation modulus by nanoindentation. Metallogr., Microstruct., Anal. 3, 5 (2014).CrossRefGoogle Scholar
Materna, A., Haušild, P., and Nohava, J.: A numerical investigation of the effect of cubic crystals orientation on the indentation modulus. Acta Physica Polonica, A 128, 693 (2015).CrossRefGoogle Scholar
Menčík, J. and Swain, M.V.: Characterisation of materials using micro-indentation tests with pointed indenters. Mater. Forum 18, 277 (1994).Google Scholar
Menčík, J. and Swain, M.V.: Errors associated with depth-sensing microindentation tests. J. Mater. Res. 10, 1491 (1995).Google Scholar
Fischer-Cripps, A.C.: Nanoindentation, 3rd ed. (Springer, New York, 2011).CrossRefGoogle Scholar
Hay, J.C., Bolshakov, A., and Pharr, G.M.: A critical examination of the fundamental relations used in the analysis of nanoindentation data. J. Mater. Res. 14, 2296 (1999).Google Scholar
Marc 2015: Volume A, Theory and User Information (MSC.Software Corporation, Newport Beach, 2015).Google Scholar
Matějíček, J., Nevrlá, B., Čech, J., Vilémová, M., Klevarová, V., and Haušild, P.: Mechanical and thermal properties of individual phases formed in sintered tungsten-steel composites. Acta Physica Polonica, A 128, 718 (2015).CrossRefGoogle Scholar
Christensen, R.M.: Mechanics of Composite Materials (Wiley, New York, 1979).Google Scholar
Lassner, E. and Schubert, W-D.: Tungsten: Properties, Chemistry, Technology of the Element, Alloys, and Chemical Compounds (Kluwer Academic/Plenum Publishers, New York, 1999).Google Scholar
Brožek, V., Ctibor, P., Matějíček, J., Mušálek, R., and Weiss, Z.: Tungsten coatings and free standing parts. In Proc.: Metal 2013, Tanger: Brno, Czech Republic, 2013; p. 6.Google Scholar
Shackelford, J.F., and Alexander, W.: CRC Materials Science and Engineering Handbook, 3rd ed. (CRC Press, Boca Raton, 2001).Google Scholar
Leisen, D., Kerkamm, I., Bohn, E., and Kamlah, M.: A novel and simple approach for characterizing the Young’s modulus of single particles in a soft matrix by nanoindentation. J. Mater. Res. 27, 3073 (2012).Google Scholar