Hostname: page-component-8448b6f56d-gtxcr Total loading time: 0 Render date: 2024-04-19T14:02:46.366Z Has data issue: false hasContentIssue false
  • English
  • Français

Analysis of extended dislocation faults

Published online by Cambridge University Press:  31 January 2011

Arun M. Kumar  and
John P. Hirth
Arun M. Kumar
Affiliation:
Department of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
John P. Hirth
Affiliation:
Department of Mechanical and Materials Engineering, Washington State University, Pullman, Washington 99164-2920
Get access

Abstract

The relative stability of standard extended dislocation dipoles and some new stable defects with lozenge-shaped cross sections have been numerically estimated. An earlier study of these defects in an isotropic fee structure has been extended to the anisotropic case to assess the effect of anisotropy on the calculations. The study is further extended to the case of the L12 crystal structure of the ordered alloy Ni3Al, where the Burgers vectors are large. Results indicate that the introduction of anisotropy has a small effect in determining the relative stability of extended dislocation faults. The results also show that the large values of the Burgers vectors stabilize the arrays in Ni3Al and that the most stable defect favored is the screw lozenge array LD.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 7 , July 1992 , pp. 1718 - 1721
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Kumar, A. M. and Hirth, J. P., Philos. Mag. A 65, 841 (1992).CrossRefGoogle Scholar
2.Mader, S., Electron Microscopy and Strength of Crystals, edited by Thomas, G. and Washburn, J. (New York, Interscience, 1963), p. 183Google Scholar
3.Seeger, A., Disc. Faraday Soc. 38, 103 (1964).Google Scholar
4.Steeds, J. W., Anisotropic Elastic Theory of Dislocations (Clarendon Press, Oxford, 1973), p. 103.Google Scholar
5.Hirth, J. P. and Lothe, J., Theory of Dislocations, 2nd ed. (John Wiley, New York, 1982), p. 445.Google Scholar
6.Yoo, M. H., in High-Temperature Ordered Intermetallic Alloys II, edited by Stoloff, N. S., Koch, C. C., Liu, C. T., and Izumi, O. (Mater. Res. Soc. Symp. Proc. 81, Pittsburgh, PA, 1987), p. 208.Google Scholar
7.Caillard, D., Clement, N., and Couret, A., Philos. Mag. Lett. 56, 263 (1988).CrossRefGoogle Scholar
8.Couret, A. and Caillard, D., Philos. Mag. A 59, 783 (1989).CrossRefGoogle Scholar
9.Kawabata, T., Abumiya, T., Kanai, T., and Izumi, O., Acta Metall. et Mater. 38, 1381 (1990).CrossRefGoogle Scholar
10.Greenburg, B. A., Anisimov, V. I., Gornostirev, Yu. N., and Taluts, G. G., Scripta Metall. 22, 859 (1988).CrossRefGoogle Scholar
11.Kear, B. H. and Wilsdorf, H. G. F., Trans. AIME 224, 382 (1962).Google Scholar
12.Paidar, V., Pope, D. P., and Vitek, V., Acta Metall. 32, 435 (1984).CrossRefGoogle Scholar